光電產業蓬勃發展帶動光學零組件需求大增，光學透鏡為常見之光學元件，可分為光學玻璃與光學塑膠兩類，本研究主要探討塑膠加工於光學透鏡之成形，其加工方法為射出成形；射出成形為成本低、速度快、良率穩定、生產效率高之一次成形加工技術，用於光學塑膠透鏡成形不需拋光、研磨之二次加工，生產時間縮短與成本降低為其優勢。然而，塑膠透鏡於射出成形往往伴隨雙折射現象存在，產生之光程差已無法透過組合透鏡等方法做矯正，檢測時雙折射過大即為廢品，此為射出成形極待解決之問題。

因射出成形鏡片之光學品質主要由幾何誤差與殘留雙折射所構成，本文使用實驗設計法針對光學透鏡幾何誤差與雙折射影響因子分析探討，為提高良率、節省物料成本與成形時間，射出成形因子分析以確保鏡片幾何尺寸與降低雙折射實重要關鍵，同時以結合模流分析與光學模擬，期能藉光學模擬即能預測成形之鏡片光學品質。

As the prosperous growth in electro-optics industry, the demand on optical components has grown significantly as well. Among the optical components, optical lenses are typically categorized as either plastic or glass type. The objective of this study is to investigate the injection molding of plastic lenses which are known for the process with low cost, high volume, good yields, and high efficiency. Plastics lenses do not need polishing and relevant post processing steps which results in reduction of production times and costs. Nevertheless, birefringence embedded in the lenses have made the optical path difference in lens components too large to be compensated so that scraps becomes a major problem in the industry which needs to be resolved today.
Because the optical qualities of injection molded lenses consist of geometric errors and residual birefringence, analysis of contributing factors are conducted with experimental methods for efficiency improvement, cost reduction, and time saving. The key is to get hold of process control factors for combining the optical analysis into flow analysis programs so that optical qualities can be successfully predicted.

[1] A. I. Isayev, （1983）“Orientation Development in the Injection Molding of Amorphous Polymers”, Polymer Engineering and Science, Vol.23, No.5, pp.271~284.
[2] J. W. Dally and W. F. Riley, (1991) Experimental Stress Analysis, McGraw-Hill, Inc., New York, N. Y.
[3] B. Sanschagrin, （1983）“Process Control of Injection Molding”, Polymer Engineering and Science, Vol. 23, No. 8, pp.431-438.
[4] X. Lu and L. S. Khim, （2001）“A Statistical Experimental Study of The Injection Molding of Optical Lenses”, Journal of Materials Processing Technology, Vol. 113, pp.189-195.
[5] B. Fan and D. Kazmer, （2003）“Simulation of Optical Media Molding”, ANTEC Technical Paper, pp.622-626.
[6] Y. B. Lee and T. H. Kwon, （2001）“Modeling and Numerical Simulation of Residual Stresses and Birefringence in Injection Molded Center-gated Disks”, Journal of Materials Processing Technology, Vol. 111, pp.214-218.
[7] R. Pantani, A. Sorrentino, V. Speranza, and G. Titomanlio, （2004） “Molecular Orientation In Injection Molding: Experiments and Analysis”, Rheol Acta, Vol. 43, pp.109-118.
[8] R. Pantani, （2005）“Validation of a Mode to Predict Birefringence In Injection Molding”, European Polymer Journal, Vol. 41, pp.1484-1492.
[9] T. C. Jan and K. T. O’Brien, （1993）“A User-Friendly Interactive Expert System for the Injection Moulding of Engineering Thermoplastics”, International Journal of Advanced Manufacturing Technology, Vol. 8, No. 1, pp.42-51.
[10] 張光榮，”射出成形機之程序控制”，國立清華大學動機系碩士論文，1996。
[11] 林金佑，”CAE整合系統應用於智慧型射出成形程序控制之研究”，國立清華大學動機系碩士論文，1997。
[12] 張榮語著，「射出成型模具設計」，高立圖書有限公司，三刷，2001年。
[13] E. Riande and E. Saiz, (1992) Dipole Moments and Birefringence of Polymers, Prentice-Hall, Inc., New Jersey.
[14] E. Hecht, (2002) Optics, Perason Education, Inc., New York, N. Y.
[15] A. W. Birey, B. Haworth, and J. Batchelor, (1992) Physics of Plastics, Hanser Publishers, Inc., New York, N. Y.
[16] http://www.zeon.co.jp/, ZEON, Chiyoda-Ku, Tokyo, Japan.
[17] http://www.breault.com/, BRO, Tucson, Arizona, U. S. A.
[18] D. C. Montgomery, (2001) Design and Analysis of Experiments, John Wiley and Sons, Inc., New York, N. Y.
[19] R. H. Myers and D. C. Montgomery, (2002) Response Surface Methodology, John Wiley and Sons, Inc., New York, N. Y.