簡易檢索 / 詳目顯示

回結果列表
研究生： 謝惠安
Hsieh, Hui-An
論文名稱： 浮動孔隙瓦片複合軸承系統之設計與分析
Design and Analysis of Floating Porous Pads Bearing System
指導教授： 蕭德瑛
Shaw, Dein
口試委員: 宋震國
Sung, Cheng-Kuo
林士傑
Lin, Shih-Chieh
陳明飛
Chen, Ming-Fei
康淵
Kang, Yuan
鄭璧瑩
Cheng, Pi-Ying
學位類別： 博士
Doctor
系所名稱： 工學院 - 動力機械工程學系
Department of Power Mechanical Engineering
論文出版年： 2019
畢業學年度： 108
語文別： 中文
論文頁數： 126
中文關鍵詞： 孔隙瓦片 、浮動油腔環 、靜壓效應 、動壓效應 、液靜壓軸承
外文關鍵詞： Porous pad, Floating bearing, Hydrostatic effect, Hydrodynamic effect, Hydrostatic bearing
相關次數： 點閱：1  下載：0 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • 本研究的研究方向為設計及分析浮動孔隙瓦片複合軸承系統，所做的研究中包含了三種以液靜壓軸承為基礎的嶄新軸承設計:孔隙瓦片軸承與浮動油腔環軸承及浮動孔隙瓦片複合軸承。孔隙瓦片軸承利用裝入液靜壓油腔的孔隙瓦片來增強主軸轉動時產生的動壓效應，使其在高速下有較高的承載力。浮動油腔環軸承則將液靜壓油腔改成可移動的浮動油腔環，並以密封環與軸套限制其自由度，在油腔環及密封環之間形成外油腔，其油腔環與與外油腔之壓力差能使主軸朝偏心的反方向位移，在靜止與低速下能降低主軸的偏心率。為了增強軸承之性能尚發展另一個浮動孔隙瓦片複合軸承，此軸承則結合了前兩者的優點，在低速與高速下皆能有超越液靜壓軸承的表現。本研究分析了孔隙瓦片軸承、浮動油腔環軸承與浮動孔隙瓦片複合軸承的各項參數對承載力、剛度、流量與摩擦係數等軸承性能的影響，並給出詳盡的圖表以供設計參考。

    The purpose of this study is to design and analyze three kinds of bearings which include a porous pads bearing, a floating bush bearing, and a hybrid bearing which consists both the floating bush bearing and the porous pads bearing. These three bearings have better performance than the traditional hydrostatic bearing in different ways. For the porous pads bearing, the embedded porous pads in recesses were studied first, which has a stronger hydrodynamic effect and higher load capacity in high shaft speed. Then the floating bush bearing which contains a hydrostatic bearing bush, several compressible sealing rings, and an outer bush is studied. The outer recesses formed between the hydrostatic bearing bush, the sealing rings and the outer bush provide outside pressures to adjust the position of the hydrostatic bearing bush. It compensates the eccentricity of the shaft by moving with the shaft with the hydrostatic bearing bush to its original position, and usually, its performance is good at low shaft speed. The floating porous pads bearing which combines both advantages of two previous bearings outperforms the hydrostatic bearing in either low and high shaft speed. This study analyzed the influence of the bearing parameters of these three kinds of bearings on the load capacity, the attitude angle, the stiffness, the flow rate, and the friction.

    中文摘要 i Abstract ii 誌謝 iii 目錄 iv 圖目錄 viii 表目錄 xiii 符號表 xvi 第一章 導論 1 1.1 研究背景 1 1.2 文獻回顧 3 1.2.1 液靜壓軸承與混壓軸承研究 3 1.2.2 孔隙軸承研究 5 1.2.3 浮動環軸承研究 7 1.3 研究目標與方法 8 1.4 論文架構 9 第二章 液壓軸承理論 10 2.1 流體力學理論 10 2.1.1 納維爾-史托克斯方程式 10 2.1.2 雷諾數 13 2.1.3 雷諾方程式 16 2.1.4 平板流 17 2.1.5 動壓效應 18 2.2 液靜壓軸承模型 19 2.2.1 液靜壓軸承結構 19 2.2.2 液靜壓軸承理論 20 2.2.3 液靜壓軸承計算流程 24 2.2.4 液靜壓軸承性能參數 26 2.2.5 參考文獻驗證 27 第三章 孔隙瓦片軸承設計 29 3.1 孔隙瓦片軸承構型與作動原理 29 3.2 孔隙瓦片軸承理論模型 30 3.2.1 孔隙區的修正雷諾方程式 31 3.2.2 區域因子 34 3.2.3 無因次化 34 3.2.4 壓力分佈 36 3.3 孔隙瓦片軸承之ANSYS模擬與實驗驗證 38 3.3.1 幾何模型建立 38 3.3.2 網格劃分 39 3.3.3 邊界條件 40 3.3.4 油腔壓力疊代 41 3.3.5 驗證結果 42 3.3.6 實驗比較 44 3.4 孔隙瓦片軸承參數與性能分析 45 3.4.1 油腔包角 46 3.4.2 長徑比 49 3.4.3 軸封寬比 51 3.4.4 進給係數 53 3.4.5 滑移係數 55 3.4.6 無因滲透因子 57 3.4.7 節流比 59 3.4.8 孔隙瓦片軸承與液靜壓軸承之比較 61 3.5 討論 64 第四章 浮動油腔環軸承設計 65 4.1 浮動油腔環軸承構型與作動原理 65 4.2 浮動油腔環軸承理論模型 67 4.2.1 外油腔靜壓力 68 4.2.2 密封環彈性力 69 4.2.3 密封環參數限制 71 4.2.4 絕對偏心率 72 4.3 ANSYS模擬驗證理論模型 73 4.3.1 幾何模型建立 73 4.3.2 網格劃分 75 4.3.3 邊界條件 76 4.3.4 模擬軟體驗證結果 78 4.4 浮動油腔環軸承參數與性能分析 78 4.4.1 外油腔包角 79 4.4.2 外腔軸長比 82 4.4.3 無因彈性係數 85 4.4.4 初始間隙比 88 4.4.5 間隙油膜比 91 4.4.6 直徑比 94 4.5 討論 97 第五章 浮動孔隙瓦片複合軸承設計 99 5.1 軸承構型與作動原理 99 5.2 浮動孔隙瓦片複合軸承參數與性能分析 100 5.2.1 外油腔包角 101 5.2.2 外腔軸長比 104 5.2.3 無因彈性係數 107 5.2.4 初始間隙比 110 5.2.5 間隙油膜比 113 5.2.6 直徑比 116 5.3 討論 119 第六章 結論與未來展望 120 6.1 結論 120 6.2 未來展望 122 參考文獻 123

    [1] Odonoghue JP, Rowe WB, Hooke CJ. Design of hydrostatic bearings using an operating parameter. Wear. 1969;14:355-62.
    [2] Rowe WB, O'Donoghue JP, Cameron A. Optimization of externally pressurized bearings for minimum power and low temperature rise. Tribology. 1970;3:153-7.
    [3] Davies PB. A general analysis of multi-recess hydrostatic journal bearings. Proceedings of the Institution of Mechanical Engineers. 1969;184:827-38.
    [4] Ghosh B. An exact analysis of a hydrostatic journal bearing with a large circumferential sill. Wear. 1972;21:367-75.
    [5] Ghosh B. Load and flow characteristics of a capillary-compensated hydrostatic journal bearing. Wear. 1973;23:377-86.
    [6] Leonard R, Rowe WB. Dynamic force coefficients and mechanism of instability in hydrostatic journal-bearings. Wear. 1973;23:277-82.
    [7] Rowe WB, Koshal D, Stout KJ. Investigation of recessed hydrostatic and slot-entry journal bearings for hybrid hydrodynamic and hydrostatic operation. Wear. 1977;43:55-69.
    [8] Ghosh MK, Majumdar BC. Design of multi-recess hydrostatic oil journal bearings. Tribol Int. 1980;13:73-8.
    [9] Sharma SC, Jain SC, Sinhasan R, Shalia R. Comparative study of the performance of six-pocket and four-pocket hydrostatic/hybrid flexible journal bearings. Tribol Int. 1995;28:531-9.
    [10] Braun MJ, Choy FK, Zhou YM. The effects of a hydrostatic pocket aspect ratio, supply orifice position, and attack angle on steady-state flow patterns, pressure, and shear characteristics. Journal of Tribology. 1993;115:678-85.
    [11] Braun MJ, Dzodzo M. Effects of the feedline and the hydrostatic pocket depth on the flow pattern and pressure distribution. Journal of Tribology. 1995;117:224-32.
    [12] Chen CH, Kang Y, Huang YN, Chu CH, Teng JT. The restrictive effects of capillary compensation on the stability of the Jeffcott rotor-hybrid bearing system. Tribol Int. 2002;35:849-55.
    [13] Chen CH, Kang Y, Huang YN, Chu CH, Teng YT. The restrictive effects of orifice compensation on the stability of the Jeffcott rotor-hybrid bearing system. Ind Lubr Tribol. 2002;54:255-61.
    [14] Chen CH, Kang Y, Huang CC. The influences of orifice restriction and journal eccentricity on the stability of the rigid rotor-hybrid bearing system. Tribol Int. 2004;37:227-34.
    [15] Chen CH, Kang Y, Chang YP, Lee HH, Shen PC. Influences of recess depth on the stability of the Jeffcott rotor supported by hybrid bearings with orifice restrictors. Ind Lubr Tribol. 2005;57:41-51.
    [16] Chen CH, Kang Y, Chang Y-P, Wang Y-P, Lee H-H. Influence of restrictor on stability of the rigid rotor–hybrid bearing system. Journal of Sound and Vibration. 2006;297:635-48.
    [17] Chen CH, Chang YP, Lee HH, Wang YP, Kang Y. The influences of capillary restriction and journal eccentricity on the stability of the rigid rotor-hybrid bearing system. Ind Lubr Tribol. 2007;59:46-51.
    [18] 陳明飛, 黃韋倫, 楊忠衡. Study on the aerodynamic effect and misalignment influence of journal gas bearing for high speed electro-spindle. 中國機械工程學刊. 2011;32:341-8.
    [19] Morgan V, Cameron A. Mechanism of lubrication in porous metal bearings. Proceedings of the Conference on Lubrication and Wear, Institution of Mechanical Engineers, London1957. p. 151-7.
    [20] Cusano C. Lubrication of porous journal bearings. Journal of Lubrication Technology. 1972;94:69-73.
    [21] Mourzenko VV, Thovert JF, Adler PM. Permeability of a single fracture - validity of the Reynolds-equation. Journal De Physique Ii. 1995;5:465-82.
    [22] D'Agostino V, Senatore A. Analytical solution for two-dimensional Reynolds equation for porous journal bearings. Ind Lubr Tribol. 2006;58:110-7.
    [23] van Buuren SW, Hetzler H, Hinterkausen M, Seemann W. Novel approach to solve the dynamical porous journal bearing problem. Tribol Int. 2012;46:30-40.
    [24] Beavers GS, Joseph DD. Boundary conditions at a naturally permeable wall. Journal of Fluid Mechanics. 1967;30:197-207.
    [25] Saleh S, Thovert JF, Adler PM. Flow along porous media by partical image velocimetry. AIChE Journal. 1993;39:1765-76.
    [26] Murti PRK. Effect of slip-flow in narrow porous bearings. Journal of Lubrication Technology-Transactions of the Asme. 1973;95:518-23.
    [27] Chandra M, Malik M, Sinhasan R. Investigation of slip effects in plane porous journal bearings. Wear. 1981;73:61-72.
    [28] Lin JR, Hwang CC. Lubrication of short porous journal bearings — use of the Brinkman-extended Darcy model. Wear. 1993;161:93-104.
    [29] Chattopadhyay AK, Majumdar BC. Steady-state solution of finite hydrostatic porous oil journal bearings with tangential velocity slip. Tribol Int. 1984;17:317-23.
    [30] Chattopadhyay AK, Majumdar BC, Rao NS. Stability of a rigid rotor in finite externally pressurized oil journal bearings with slip. Journal of Tribology. 1987;109:301-6.
    [31] Etsion I, Michael O. Enhancing sealing and dynamic performance with partially porous mechanical face seals. Tribol Trans. 1994;37:701-10.
    [32] Kalavathi GK, Dinesh PA, Gururajan K. Influence of roughness on porous finite journal bearing with heterogeneous slip/no-slip surface. Tribol Int. 2016;102:174-81.
    [33] Eder SJ, Ielchici C, Krenn S, Brandtner D. An experimental framework for determining wear in porous journal bearings operated in the mixed lubrication regime. Tribol Int. 2018;123:1-9.
    [34] Cusano C. Lubrication of a two-layer porous journal bearing. Journal of Mechanical Engineering Science. 1972;14:335-9.
    [35] Cusano C. Analytical investigation of an infinitely long, two-layer, porous bearing. Wear. 1972;22:59-67.
    [36] Saha N, Majumdar BC. Steady-state and stability characteristics of hydrostatic two-layered porous oil journal bearings. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. 2004;218:99-108.
    [37] Rao T, Rani AMA, Nagarajan T, Hashim FM. Analysis of journal bearing with double-layer porous lubricant film: influence of surface porous layer configuration. Tribol Trans. 2013;56:841-7.
    [38] Kumar MP, Samanta P, Murmu NC. Investigation of velocity slip effect on steady state characteristics of finite hydrostatic double-layered porous oil journal bearing. Proc Inst Mech Eng Part J-J Eng Tribol. 2015;229:773-84.
    [39] Kumar MP, Samanta P, Murmu NC. Rigid rotor stability analysis on finite hydrostatic double-layer porous oil journal bearing with velocity slip. Tribol Trans. 2015;58:930-40.
    [40] Orcutt FK, Ng CW. Steady-state and dynamic properties of floating-ring journal bearing. Journal of Lubrication Technology. 1968;90:243-53.
    [41] Nikolajs.Jl. Effect of variable viscosity on stability of plain journal-bearings and floating-ring journal-bearings. Journal of Lubrication Technology-Transactions of the Asme. 1973;95:447-56.
    [42] Mokhtar MOA. Floating ring journal bearings: theory, design and optimization. Tribol Int. 1981;14:113-9.
    [43] Cheong YM, Kim KW. An analysis of the circumferentially grooved floating ring journal bearing considering the variation of cavitation region. JSME Int J Ser C-Dyn Control Robot Des Manuf. 1994;37:804-11.
    [44] Malik M. Externally-pressurized gas-lubricated floating-ring porous journal bearings .1. Steady-state analysis. Proceedings of the Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering Science. 1984;198:213-24.
    [45] Malik M, Hori Y. Externally-pressurized gas-lubricated floating-ring porous journal bearings .2. Dynamic state analysis. Proceedings of the Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering Science. 1986;200:101-9.
    [46] Zhang RQ, Chang HS. Stability of a new type of hydrostatic hydrodynamic floating ring gas bearing. Tribol Trans. 1999;42:331-7.
    [47] Hong G, Xinmin L, Xiaoling W, Shaoqi C. Performance of flat capillary compensated deep/shallow pockets hydrostatic/hydrodynamic journal-thrust floating ring bearing. Tribol Trans. 2009;52:204-12.
    [48] Hamrock BJ, Schmid SR, Jacobson BO. Fundamentals of fluid film lubrication: Taylor & Francis; 2004.
    [49] 張金正. 多孔瓦片靜動壓混合軸承之改良與精進. 新竹市: 國立清華大學; 2019.
    [50] 陳翊云. 具浮動油腔環之液靜壓軸承設計與測試. 新竹市: 國立清華大學; 2017.

    QR CODE