半導體製程中，適當的活化能提升元件電特性、改善界面層品質、降低漏電流等，而合適的佈植深度也能提高汲極電流、減少接面之反向電流，摻雜活化及離子佈植在製程中扮演著至關重要的角色。本論文應用遠紅外光(10.6μm)及綠光(532nm)退火，利用綠光短波長的特性主要活化表層，遠紅外光則活化源汲極深處，期望能改善傳統快速熱退火的缺陷。而雙重離子佈植則是以磷建立較深的接面減少接面漏電流，以砷建立較淺層之接面，提供通道反轉所需的載子。
在論文的第一部分，利用兩種不同波長的雷射退火搭配較低溫的快速熱退火，既可以降低製程的熱預算，進而抑制源極與汲極在摻雜活化後因高溫導致的雜質擴散情形嚴重而造成的漏電，而經過雷射退火後閘極介電層的粗糙度也會變小。實驗結果顯示經過紅外光及綠光雷射退火後，電晶體特性如汲極電流(4.011x10-5 A/μm)、最大轉導值(38.66 μA/V)及次臨界擺幅特性(約68.7 V/dec)，電性比起傳統的熱退火有著顯著的提升。
第二部分，文獻中提到雙重離子佈植法可以提升元件的電特性，因此設計出五個不同的佈植參數來做平面式電晶體。藉由第一次磷的植入對表面的矽進行預先非晶化植入，使得第二次的砷可以建立較淺層的接面，比起單次離子植入能擁有更低的接面漏電流，而臨界電壓的漂移情況也比單次離子植入來的穩定。
延續上一個部分，我們發現雙重離子佈植法有開關特性不佳的缺點，因此在第三部分中，我們挑選幾個較佳的佈植參數應用在SOI-FinFET的結構上，期望藉由SOI基板及鰭式電晶體的優勢，在維持汲極電流的同時大幅降低漏電流。實驗結果發現磷40keV/砷40keV有最佳的汲極電流(6.814 x10-5 A/μm)、開關特性比(1.234 x108 )、最大轉導值(49.36μA/V)，發現在鰭式電晶體的結構上雙重離子佈植法可以進一步提升電流特性。

Electrical characteristics and interface layer quality can be improved, and leakage current can be reduced in FinFET by appropriate activation process. The drain current can be enhanced and reverse current of junction can be decreased by suitable depth of ion implantation. Doping activation and ion implantation always play important roles in electrical characteristics of FinFET. In this thesis, far infrared light(10.6μm) and visible green light(532nm) were used for annealing dopants. The short wavelength of green light is used to activate the surface layer, and the far infrared light is intended to activate deeper region of source-drain. Laser annealing is expected to reduce the defects, which are generally caused by traditional rapid thermal annealing. Double ion implantations include a deep junction with Phosphorus to reduce junction leakage, and a shallow junction with Arsenic to provide sufficient channel carrier at inversion.
On the first part of the thesis, laser annealing with two wavelengths and rapid thermal annealing are applied to the thermal budget of fabrication process, which may suppress leakage current caused by diffusion after high temperature. It is known that the roughness of gate dielectric are less after laser annealing treatment. The experimental results show that the excellent electrical characteristics of FinFET are obtained such as the drain current (4.011x10-5 A/μm), the maximum transconductance value (38.66 μA/V) and the sub-threshold swing characteristics (about 68.7 V/dec) after red and green laser annealing. Electrical properties of FinFET with laser annealing using two wavelengths are much improved as compared to these with traditional thermal annealing.
In the second part, double ion implantations method are studied to increase on current of MOSFET, so five devices with different implantation parameters are designed. The surface is pre-amorphized by Phosphorus implantation, and then the shallow junction is formed by an Arsenic ion implantation. The junction leakage current of device with double ion implantations is lower than that with single one. The variation of threshold voltage with double ion implantations is more stable than that with single one.
The on/off ratio of device with double ion implantations is poor as found in previous part. In the third part, various implantation energy for both shallow and deep dopants on SOI FinFET are investigated to reduce the leakage current and keep large drain current. The results show that FinFET with S/D junction formed by phosphorus 40keV/arsenic 40keV has the highest drain current (6.814 x10-5 A/μm), on/off ratio (1.234 x108), maximum transconductance value (49.36μA/V), it is also found that double ion implantation can further improve the on current characteristics.

[1] J. Stathis and D. DiMaria, "Reliability projection for ultra-thin oxides at low voltage," in Electron Devices Meeting, 1998. IEDM'98. Technical Digest., International, 1998, pp. 167-170: IEEE.
[2] D. K. Schroder, "Contact resistance and Schottky barriers," Semiconductor Material and Device Characterization, Third Edition, pp. 127-184, 2006.
[3] M. Agostinelli, M. Alioto, D. Esseni, and L. Selmi, "Leakage–delay tradeoff in FinFET logic circuits: A comparative analysis with bulk technology," IEEE Transactions on Very Large Scale Integration (VLSI) Systems, vol. 18, no. 2, pp. 232-245, 2010.
[4] Y. Taur and T. H. Ning, Fundamentals of modern VLSI devices. Cambridge university press, 2013.
[5] H.-S. Wong, "Beyond the conventional transistor," IBM Journal of Research and Development, vol. 46, no. 2.3, pp. 133-168, 2002.
[6] M. Houssa et al., "Electrical properties of high-k gate dielectrics: Challenges, current issues, and possible solutions," Materials Science and Engineering: R: Reports, vol. 51, no. 4-6, pp. 37-85, 2006.
[7] H. Sasaki et al., "1.5 nm direct-tunneling gate oxide Si MOSFET's," IEEE Transactions on Electron Devices, vol. 43, no. 8, pp. 1233-1242, 1996.
[8] S. Saito, "Unified mobility model for high-k gate stacks," IEDM Tech. Digest, 2003, 2003.
[9] R. People and J. Bean, "Calculation of critical layer thickness versus lattice mismatch for Ge x Si1− x/Si strained‐layer heterostructures," Applied Physics Letters, vol. 47, no. 3, pp. 322-324, 1985.
[10] C. Manoj, M. Nagpal, D. Varghese, and V. R. Rao, "Device design and optimization considerations for bulk FinFETs," IEEE transactions on electron devices, vol. 55, no. 2, pp. 609-615, 2008.
[11] B. Parvais et al., "The device architecture dilemma for CMOS technologies: opportunities & challenges of Finfet over planar mosfet," in VLSI Technology, Systems, and Applications, 2009. VLSI-TSA'09. International Symposium on, 2009, pp. 80-81: IEEE.
[12] C. Kang et al., "Effects of ALD TiN Metal Gate Thickness on Metal Gate/High-k Dielectric SOI FinFET Characteristics," in International SOI Conference, 2006 IEEE, 2006, pp. 135-136: IEEE.
[13] T. Hayashida et al., "Fin-height effect on poly-Si/PVD-TiN stacked-gate FinFET performance," IEEE Transactions on Electron Devices, vol. 59, no. 3, pp. 647-653, 2012.
[14] C. Y. Kang et al., "Effects of Film Stress Modulation Using TiN Metal Gate on Stress Engineering and Its Impact on Device Characteristics in Metal Gate/High-k Dielectric SOI FinFETs," IEEE Electron Device Letters, vol. 29, no. 5, pp. 487-490, 2008.
[15] M. Yang et al., "High performance CMOS fabricated on hybrid substrate with different crystal orientations," in Electron Devices Meeting, 2003. IEDM'03 Technical Digest. IEEE International, 2003, pp. 18.7. 1-18.7. 4: IEEE.
[16] C. Kang et al., "A novel electrode-induced strain engineering for high performance SOI FinFET utilizing Si (1hannel for Both N and PMOSFETs," in Electron Devices Meeting, 2006. IEDM'06. International, 2006, pp. 1-4: IEEE.
[17] G. Vellianitis et al., "The Influence of TiN Thickness and SiO2 Formation Method on the Structural and Electrical Properties of TiN/HfO2/SiO2 Gate Stacks," IEEE Transactions on Electron Devices, vol. 56, no. 7, pp. 1548-1553, 2009.
[18] I.-W. Wu, T.-Y. Huang, W. B. Jackson, A. G. Lewis, and A. Chiang, "Passivation kinetics of two types of defects in polysilicon TFT by plasma hydrogenation," IEEE electron device letters, vol. 12, no. 4, pp. 181-183, 1991.
[19] N. Nickel, P. Mei, and J. Boyce, "On the nature of the defect passivation in polycrystalline silicon by hydrogen and oxygen plasma treatments," IEEE Transactions on Electron Devices, vol. 42, no. 8, pp. 1559-1560, 1995.
[20] D. Kaplan, N. Sol, G. Velasco, and P. Thomas, "Hydrogenation of evaporated amorphous silicon films by plasma treatment," Applied Physics Letters, vol. 33, no. 5, pp. 440-442, 1978.
[21] C. Seager and D. Ginley, "Passivation of grain boundaries in polycrystalline silicon," Applied Physics Letters, vol. 34, no. 5, pp. 337-340, 1979.
[22] T. Makino and H. Nakamura, "The influence of plasma annealing on electrical properties of polycrystalline Si," Applied Physics Letters, vol. 35, no. 7, pp. 551-552, 1979.
[23] D. Campbell, "Enhanced conductivity in plasma‐hydrogenated polysilicon films," Applied Physics Letters, vol. 36, no. 7, pp. 604-606, 1980.
[24] N. Willems, U. Wejinya, and Z. Dong, "Temperature treatment on Silicon Nanowires for reliability studies," in Nanotechnology (IEEE-NANO), 2013 13th IEEE Conference on, 2013, pp. 321-324: IEEE.
[25] A. F. i Morral and P. R. i Cabarrocas, "Etching and hydrogen diffusion mechanisms during a hydrogen plasma treatment of silicon thin films," Journal of non-crystalline solids, vol. 299, pp. 196-200, 2002.
[26] J.-S. Lee, Y.-K. Choi, D. Ha, S. Balasubramanian, T.-J. King, and J. Bokor, "Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs," IEEE Electron Device Letters, vol. 24, no. 3, pp. 186-188, 2003.
[27] 馮浩庭, "熱退火及通道高度對矽在絕緣體上鰭式電晶體電特性影響之研究," 清華大學工程與系統科學系學位論文, pp. 1-95, 2015.
[28] Y. Zhao, M. Takenaka, and S. Takagi, "Comprehensive understanding of surface roughness and Coulomb scattering mobility in biaxially-strained Si MOSFETs," in Electron Devices Meeting, 2008. IEDM 2008. IEEE International, 2008, pp. 1-4: IEEE.
[29] D. Gilmer et al., "Laser anneal to enable ultimate cmos scaling with pmos band edge metal gate/high-k stacks," in Solid-State Device Research Conference, 2006. ESSDERC 2006. Proceeding of the 36th European, 2006, pp. 351-354: IEEE.
[30] H.-D. Lee and Y.-J. Lee, "Arsenic and phosphorus double ion implanted source/drain junction for 0.25 and sub-0.25-μm MOSFET technology," IEEE Electron Device Letters, vol. 20, no. 1, pp. 42-44, 1999.
[31] F.-C. Wang and C. Bulucea, "BF 2 and boron double-implanted source/drain junctions for sub-0.25-μm CMOS technology," IEEE Electron Device Letters, vol. 21, no. 10, pp. 476-478, 2000.
[32] T. Yamashita et al., "High performance 65nm soi transistors using laser spike annealing," in Solid-State Device Research Conference, 2006. ESSDERC 2006. Proceeding of the 36th European, 2006, pp. 347-350: IEEE.
[33] S. Kerdilès et al., "Dopant activation and crystal recovery in arsenic-implanted ultra-thin silicon-on-insulator structures using 308nm nanosecond laser annealing," in Junction Technology (IWJT), 2016 16th International Workshop on, 2016, pp. 72-75: IEEE